This post listed below involving How to Install a Bathtub is relatively insightful. Have a go and draw your own assumptions.
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the project can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit attempting it. Instead of hiring a professional to take over a halfway-completed task, it is far better to think about employing one before you begin. Chances are you might require a specialist plumber to make tube links.
This write-up will certainly assist you set up a new tub in your restroom if you have actually currently gotten a new tub and don't require to transform the setup of your previous water system pipelines.
Your tools and material list need to make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the limited gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Secure the faucet in position with the producer given backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the tub up until the level reviews level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints and new pipework for leaks and tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub should wait until the bathtub has been used at least once as this will certainly resolve it right into its last placement.
Planning for the Setup
First of all, the supporting framework supplied with the bathroom must be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its final position.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that piece of writing on Tools You Need to Install a New Bathtub while doing a search on the internet. So long as you enjoyed reading our blog post if you please don't forget to share it. Many thanks for your time. Come back soon.
Call Us Now